Troubleshooting Your Vexilar Ice Fishing Flasher: A Guide

Troubleshooting

If you’re a Vexilar ice fishing enthusiast, then you know that having a working flasher is key to catching fish. Unfortunately, things sometimes go wrong with these devices, and it can be difficult to determine what the problem is. In this guide, we will walk you through the most common problems that people experience with their Vexilar flashers, and provide solutions for fixing them. We hope that this information will help you get back out on the ice and start catching some fish!

Vexilar has been making quality ice fishing products for over 60 years, and their flashers are some of the best on the market. However, even the best devices can have problems from time to time. If you’re having trouble with your Vexilar flasher, check out our troubleshooting guide below.

Let us now dive into the common problems that people have with their Vexilar flashers.

My Vexilar Doesn’t Turn On

This is perhaps the most common problem that people experience with their Vexilar flashers. There are a few things that could be causing this issue.

First, make sure that the batteries are properly installed and have enough power. Always make sure to have a voltage meter on hand to check the voltage of your batteries. If the batteries are low, they will need to be replaced.

A battery reading of around 12.5 V is considered acceptable, but anything below 12 V is too low and needs to be replaced.

Pinched wires can also cause the Vexilar flasher to fail to turn on. Inspect all of the wires running to and from the device, and make sure that none of them are damaged or pinched.

If everything looks good with the batteries and wires, then the problem may be with the motor. If the motor is the issue it needs to be sent to the company for repairs.

The Vexilar company provides a great warranty on their products, so if you think that the problem is with the motor, don’t hesitate to send it in for repairs.

Another possible issue is that the battery terminals may be corroded. This can happen if you don’t clean and maintain your flasher regularly. Use a cotton swab or toothbrush to clean the terminals, and then try again.

Still, having trouble? Try these other troubleshooting tips:

-Check the owner’s manual for your specific model of Vexilar. It may have additional troubleshooting tips that can help you fix the problem.

-Try resetting the device by unplugging it from the power source and then plugging it back in.

-If you’re still having trouble, contact Vexilar customer service. They will be able to help you troubleshoot the problem and get your flasher working again.

New Vexilar Makes Screechy Sound

This is quite normal for a new Vexilar flasher. It is caused by the bearings in the motor being new and tight. The screeching noise should go away after a few days of use as the bearings break-in.

However, if your old Vexilar starts making this noise, it is a sign that the bearings need to be replaced. You can purchase a replacement kit from Vexilar or take it to a qualified technician.

On a side note, the FLX-28 is less noisy than other models and doesn’t require a break-in period.

Keep Showing Different Depths

There are a few things that could be causing this issue.

First, make sure that the transducer is properly installed and secure. If it is loose, it will give inaccurate readings. To check the transducer hold is very near to your ear and give the wire a little tug.

You should hear a “thunk” if it is properly in place. If not, then you will need to adjust it and try again.

Second, check the area around the transducer for any debris. Sometimes ice or snow can build up and cause problems. Debris can cause false readings or interfere with the signal.

Third, make sure that the depth settings on the flasher are correct. If they are set too high, they will show false depths.

Finally, if you’re still having trouble, contact Vexilar customer service. They will be able to help you troubleshoot the problem and get your flasher working again.

Lots of Interference on Vexilar Flasher

Any seasoned angler can tell you the difference between true interference and clutter interference.

Clutter interference is when you see a lot of small and close-together arches on your flasher. This is caused by lots of other electrical noise in the area, such as other ice anglers, and power lines.

Vexilar provides an I.R interface rejection button on their flashers that helps to reduce clutter interference.

To use it, press and hold the button until you see the IR light come on. This will help to reduce the amount of electrical noise in the area and give you a clearer reading.

Vexilar Runs but Without Lights

If your Vexilar flasher turns on but doesn’t show any lights, the problem is most likely with the battery.

First, check to see if the battery is properly installed. If it is, then try replacing the battery with a new one.

If that doesn’t work, then the problem may be with the power cord. Inspect the cord for any damage or fraying. If there is damage, then you will need to replace the cord.

Still, having trouble? Contact Vexilar customer service. They will be able to help you troubleshoot the problem and get your flasher working again.

Vexilar Freezes Up

If your Vexilar flasher freezes up, there are a few things that you can try to fix the problem.

First, try resetting the device by unplugging it from the power source and then plugging it back in.

If that doesn’t work, try removing the battery and then reinstalling it.

Lots of green Light on my Vexilar flasher

If you see a lot of green lights on your Vexilar flasher, it means you are seeing lots of clutter interference.

Clutter interference is when you see a lot of small and close-together arches on your flasher. This is caused by lots of other electrical noise in the area, such as other ice anglers, and power lines.

Try by going to another location or try the I.R interface rejection button.

To use it, press and hold the button until you see the IR light come on. This will help to reduce the amount of electrical noise in the area and give you a clearer reading.

If you’re still having trouble, contact Vexilar customer service. They will be able to help you troubleshoot the problem and get your flasher working again.

Cannot See Any Jigs

If you’re not seeing any jigs on your Vexilar flasher, it could be for a few different reasons.

First, check to see if the transducer is properly installed and secure. If it is loose, it will give inaccurate readings. A faulty transducer can also cause false readings or no readings at all.

Check the angle of your transducer as well. If it is not at the correct angle, it will not give accurate readings.

Finally, make sure that the depth settings on the flasher are correct. If they are set too high, they will show false depths.

Charger Always Shows Green

If your charger always shows green, it means that the battery is fully charged.

First, check to see if the battery is properly installed. If it is, then try replacing the battery with a new one.

If that doesn’t work, then the problem may be with the power cord. Inspect the cord for any damage or fraying. If there is damage, then you will need to replace the cord.

Conclusion

If you’re having trouble with your Vexilar ice fishing flasher, don’t worry. There are a few things that you can try to fix the problem. We’ve provided a guide to troubleshooting some of the most common issues. If all of this seems too daunting, don’t worry. Low battery? Clutter interference? These are all common problems that can be easily fixed. If you’re still having trouble, contact Vexilar customer service. They will be able to help you troubleshoot the problem and get your flasher working again. So go out there and enjoy some ice fishing!